The effect of metal foam fins on the thermo-hydraulic performance of a solar air heater

Sally Q Hussien, Ammar A. Farhan

Abstract


The metal foam porosity helps the air to penetrate through the fins and extracted more heat gain from the absorber plate. In this experimental study, the effect of metallic foam fins on the thermohydraulic efficiency is investigated through a test rig built for this purpose. Fins with different metal foam pore density (PPI), and three different configurations (longitudinal, corrugated, and staggered) are attached to the back surface of the absorber plate. The experiments are conducted under Baghdad climatic conditions for February, March and April 2018. The results showed that the presence of metal foam fins provided a large surface area for convective heat transfer so that, the air temperature difference and thermal efficiency of the solar collector are increased. The maximum temperature difference for corrugated, staggered, longitudinal metallic foam, and solid longitudinal fins at an air flow rate of 0.01 m3/s is 31, 27, 23, and 17 ℃, respectively. Metal foam fins with higher PPI exhibited higher air temperature difference due to higher heat transfer surface area. The highest value of the thermal and effectiveness efficiencies for corrugated metal foam fins are 86 %, and 79 %, respectively.

Keywords


solar energy

Full Text:

PDF

References


A.E. Kabeel, M.H. Hamed, Z.M. Omara, and A.W. Kandeal, “Solar air heaters: Design configurations, improvement methods and applications–A detailed reviewâ€. Renewable and Sustainable Energy Reviews, 70, pp.1189-1206, 2017.

A.A. Farhan and H. A. Sahi, “Energy Analysis of Solar Collector With perforated Absorber Plateâ€, Journal of Engineering, 23(9), pp. 89-102, 2017.

K. Mohammadi, and M. Sabzpooshani, “Comprehensive performance evaluation and parametric studies of single pass solar air heater with fins and baffles attached over the absorber plateâ€. Energy, 57, 741-750, 2013.

H. M. Yeh, “Upward-type flat-plate solar air heaters attached with fins and operated by an internal recycling for improved performanceâ€. Journal of the Taiwan Institute of Chemical Engineers, 43(2), 235-240, 2012.

N. Moummi, S. Youcef-Ali, A. Moummi, and J.Y. Desmons, “Energy analysis of a solar air collector with rows of finsâ€. Renewable Energy, 29(13), 2053-2064, 2004.

K. Sopian, M.A. Alghoul, E. M. Alfegi, M. Y. Sulaiman, and E.A. Musa, “Evaluation of thermal efficiency of double-pass solar collector with porous–nonporous mediaâ€. Renewable Energy, 34(3), 640-645, 2009.

R. Kumar, and P. Chand, “Performance enhancement of solar air heater using herringbone corrugated finsâ€. Energy, 127, 271-279, 2017.

H. Hassan, and S. Abo-Elfadl, “Experimental study on the performance of double pass and two inlet ports solar air heater (SAH) at different configurations of the absorber plateâ€. Renewable Energy, 116, 728-740, 2018.

J. Chen, D. Yang, J. Jiang, A. Ma, and D. Song, “Research progress of phase change materials (PCMs) embedded with metal foam (a review)â€. Procedia Materials Science, 4, 389-394, 2014.

J. A. Duffie, and W. A. Beckman, Solar engineering of thermal processes. 4th ed., John Wiley & Sons 2013.

A.Cortes, and R. Piacentini, “Improvement of the efficiency of a bare solar collector by means of turbulence promotersâ€. Applied Energy, 36(4), 253-261, 1990.

J.P. Holman. Experimental Methods for Engineers, McGraw-Hill, New York, 1989.

R.J. Moffat, “Describing the uncertainties in experimental resultsâ€, Exp. Therm. Fluid Sci. 1 (1) 3–17, 1988.




DOI (PDF): https://doi.org/10.20508/ijrer.v9i2.9276.g7651

Refbacks

  • There are currently no refbacks.


Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is cited in SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics);

IJRER has been cited in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE in 2025; 

h=35,

Average citation per item=6.59

Last three Years Impact Factor=(1947+1753+1586)/(146+201+78)=5286/425=12.43

Category Quartile:Q4