Effect of Thermoelectric Cooling System on the Performance of Photovoltaic-Thermal Collector: A Review

Muhammad Ibrahim Ali Zaini, Muslizainun Mustapha, Nurul Nazli Rosli, Muhazri Abd Mutalib, Nurul Syakirah Nazri, Wan Mustafa Wan Sulong, Ahmad Fudholi

Abstract


Renewable energy (RE) is critical for the mitigation of the dependency on fossil fuel-based energy. Solar energy has a vast potential compared to other RE to replace fossil fuel. To harness solar energy, photovoltaic (PV) technology is utilised to convert light energy into electrical energy. The major drawback of PV is that its performance can be easily dropped due to an increase in the temperature of PV panels.  To address this limitation, solar thermal collectors have been developed to extract heat from PV surfaces purposely to cool them down. Numerous researchers in prior studies agreed that the combination of PV and the thermal collector as a whole system, also known as a photovoltaic-thermal (PVT) system, would be beneficial in increasing PV efficiency. There are multiple cooling systems that notably can reduce the temperature of PV panels. Water and air were used extensively before the emergence of an advanced cooling system such as nanofluid, phase change material (PCM), and thermoelectric (TE). The TE device can convert thermal energy into electricity using the Seebeck effect. Contrarily, it will act as a cooling system by supplying electricity due to the Peltier effect. The combination of PVT and TE modules (PVT-TE) is very beneficial in increasing energy production. This review paper mainly focuses on different designs of PVT-TE. The performance of PVT-TE is analysed using the first and second laws of thermodynamics. This paper found that the energy and exergy efficiency of PVT-TE is in the range of 23.21 – 81.47% and 6.39 – 16%, respectively.


Keywords


energy; renewable energy; solar energy; photovoltaic technology

Full Text:

PDF

References


N. S. Nazri, A. Fudholi, W. Mustafa, C. H. Yen, M. Mohammad, M. H. Ruslan, and K. Sopian., “Exergy and improvement potential of hybrid photovoltaic thermal/thermoelectric (PVT/TE) air collector”, Renewable Sustainable Energy Review, vol. 111, pp. 132–144, September 2019.

M. Dayer, A. S. A. Hamid, K. Sopian, A. Ibrahim, A. B. Aasam, B. Abdulsahib, and S. Rahmanian, “Performance of Combined PCM/Metal Foam-based Photovoltaic Thermal (PVT) Collector”, International Journal Of Renewable Energy Research, vol. 13, Jun 2023.

S. K. Pathak, P. O. Sharma, V. Goel, S. Bhattacharyya, H. Aybar, and J. P. Meyer, “A detailed review on the performance of photovoltaic/thermal system using various cooling methods”, Sustain. Energy Technol. Assessments, vol. 51, pp. 101844, Jun 2022.

M. A. A. Ishak, A. Ibrahim, K. Sopian, M. F. Fauzan, S. Imad, and A. S. A. Hamid “Heat Transfer Performance of a Novel Circular Flow Jet Impingement Bifacial Photovoltaic Thermal PVT Solar Collector”, International Journal Of Renewable Energy Research, vol. 13, Jun 2023.

C. Wheeley, P. Mago, and R. Luck, “Methodology to perform a combined heating and power system feasibility study for industrial manufacturing facilities”, Distrib. Gener. Altern. Energy J., vol. 27, pp. 8–32, 2012.

M. Mustapha, A. Fudholi, and K. Sopian, “Mathematical Modelling of Bifacial Photovoltaic-Thermal (BPVT) Collector with Mirror Reflector” International Journal Of Renewable Energy Research, vol. 10, Jun 2020.

P. Bevilacqua, R. Bruno, and N. Arcuri, “Comparing the performances of different cooling strategies to increase photovoltaic electric performance in different meteorological conditions”, Energy, vol. 195, pp. 116950, 2020.

S. M. Pourkiaei, M.H. Ahmadi, M.Sadeghzadeh, S. Moosavi, F. Pourfayaz, L. Chen, M. A. P. Yazdi and R. Kumar, “Thermoelectric cooler and thermoelectric generator devices: A review of present and potential applications, modeling and materials,” Energy, vol. 186, p. 115849, November 2019.

S. Thongsan, B. Prasit, T. Suriwrong, Y. Mensin, and W. Wansungnern, “Development of solar collector combined with thermoelectric module for solar drying technology,” Energy Procedia, vol. 138, pp. 1196–1201, October 2017.

H. C. Kuttarmare, R. D. Vaidya, S. M. Chaudhari, K. G. Sontakke, and Y. G. Joshi, “‘ Fabrication of Peltier Cooling System : Alternative for Refrigeration ,’” Ijariie, vol. 2, no. 3, pp. 260–264, 2016.

G. J. Snyder and E. S. Toberer, “Complex thermoelectric materials,” Nat. Mater., vol. 7, no. 2, pp. 105–114, 2008.

A. A. Khan, K. Zaimi, S. F. Sufahani, and M. Ferdows, “Mhd mixed convection flow and heat transfer of a dual stratified micropolar fluid over a vertical stretching/ shrinking sheet with suction, chemical reaction and heat source,” CFD Lett., vol. 12, no. 11, pp. 106–120, 2020.

J. Zhang H. Li, K. Ma, L. Xue, B. Han, Y. Dong, Y. Tan and C. Gu, “Design of PID temperature control system based on STM32,” IOP Conf. Ser. Mater. Sci. Eng., vol. 322, no. 7, 2018.

A. Serrat and B. Djebbar, “Mathematical Modelling of Engineering Problems,” Math. Model. Eng. Probl., vol. 9, no. 2, pp. 507–514, 2022.

K. Biswas, Z. Ren, Y. Grin, K. H. Lee, T. Mori, and L. Chen, “Thermoelectric materials science and technology toward applications,” Appl. Phys. Lett., vol. 121, no. 7, pp. 3–6, 2022.

X. Zhou, Y. Yan, X. Lu , H. Zhu, X. Han, G. Chen and Z. Ren, “Routes for high-performance thermoelectric materials,” Mater. Today, vol. 21, no. 9, pp. 974–988, November 2018.

A. R. M. Siddique, S. Mahmud, and B. Van Heyst, “A review of the state of the science on wearable thermoelectric power generators (TEGs) and their existing challenges,” Renew. Sustain. Energy Rev., vol. 73, no. January, pp. 730–744, June 2017.

B. Orr, A. Akbarzadeh, M. Mochizuki, and R. Singh, “A review of car waste heat recovery systems utilising thermoelectric generators and heat pipes,” Appl. Therm. Eng., vol. 101, pp. 490–495, May 2016.

C. Liu, Z. Zhang, Y. Peng, F. Li, L. Miao, E. Nishibori, R. Chetty, X. Bai, R. Si, J. Gao, X. Wang, Y. Zhu, N. Wang, H. Wei and T. Mori “Charge transfer engineering to achieve extraordinary power generation in GeTe-based thermoelectric materials,” Sci. Adv., vol. 9, no. 17, p. eadh0713, April 2023.

Y. Zhao, M. Lu, Y. Li, Y. Wang, and M. Ge, “Numerical investigation of an exhaust thermoelectric generator with a perforated plate,” Energy, vol. 263, no. PB, p. 125776, January 2023.

W. Zhu, Y. Deng, Y. Wang, S. Shen, and R. Gulfam, “High-performance photovoltaic-thermoelectric hybrid power generation system with optimized thermal management,” Energy, vol. 100, pp. 91–101, April 2016.

E. Shittu, M. Kolokotroni, and V. Stojceska, “Environmental impact of the high concentrator photovoltaic thermal 2000x system,” Sustain., vol. 11, no. 24, pp. 1–21, 2019.

J. Jacob, A.K. Pandey, Nasrudin Abd Rahim, Jeyraj Selvaraj, M. Samykano, R. Saidur, V.V Tyagi, “Concentrated Photovoltaic Thermal (CPVT) systems: Recent advancements in clean energy applications, thermal management and storage,” J. Energy Storage, vol. 45, no. 5, p. 103369, January 2022.

S. Shittu, G. Li, X. Zhao, J. Zhou, X. Ma, and Y. G. Akhlaghi, “Experimental study and exergy analysis of photovoltaic-thermoelectric with flat plate micro-channel heat pipe,” Energy Convers. Manag., vol. 207, no. October 2019, p. 112515, March 2020.

J. S. Choi, J. S. Ko, and D. H. Chung, “Development of a thermoelectric cooling system for a high efficiency BIPV module,” J. Power Electron., vol. 10, no. 2, pp. 187–193, 2010.

W. He, J. Zhou, C. Chen, and J. Ji, “Experimental study and performance analysis of a thermoelectric cooling and heating system driven by a photovoltaic/thermal system in summer and winter operation modes,” Energy Convers. Manag., vol. 84, pp. 41–49, August 2014.

S. Lv, Y. Ji, Z. Qian, W. He, Z. Hu, and M. Liu, “A novel strategy of enhancing sky radiative cooling by solar photovoltaic-thermoelectric cooler,” Energy, vol. 219, p. 119625, March 2021.

M. Benghanem, A. A. Al-Mashraqi, and K. O. Daffallah, “Performance of solar cells using thermoelectric module in hot sites,” Renew. Energy, vol. 89, pp. 51–59, April 2016.

R. Lamba, S. Manikandan, and S. C. Kaushik, “Performance Analysis and Optimization of Concentrating Solar Thermoelectric Generator,” J. Electron. Mater., vol. 47, no. 9, pp. 5310–5320, June 2018.

J. Zhang and Y. Xuan, “Performance improvement of a photovoltaic - Thermoelectric hybrid system subjecting to fluctuant solar radiation,” Renew. Energy, vol. 113, pp. 1551–1558, December 2017.

S. Soltani, A. Kasaeian, H. Sarrafha, and D. Wen, “An experimental investigation of a hybrid photovoltaic/thermoelectric system with nanofluid application,” Sol. Energy, vol. 155, pp. 1033–1043, October 2017.

M. . Shakouri, M.; Golzari, S.; Zamen, “Energy and Exergy Optimization of Water Cooled Thermal Photovoltaic (PV/T) System Using Genetics Algorithm,” vol. 1, no. 1, pp. 45–51, 2016.

A. S. Joshi, I. Dincer, and B. V. Reddy, “Thermodynamic assessment of photovoltaic systems,” Sol. Energy, vol. 83, no. 8, pp. 1139–1149, August 2009.

G. Contento, B. Lorenzi, A. Rizzo, and D. Narducci, “Efficiency enhancement of a-Si and CZTS solar cells using different thermoelectric hybridization strategies,” Energy, vol. 131, pp. 230–238, July 2017.

E. Yin, Q. Li, and Y. Xuan, “A novel optimal design method for concentration spectrum splitting photovoltaic–thermoelectric hybrid system,” Energy, vol. 163, pp. 519–532, November 2018.

F. Sarhaddi, S. Farahat, H. Ajam, and A. Behzadmehr, “Exergetic performance assessment of a solar photovoltaic thermal (PV/T) air collector,” Energy Build., vol. 42, no. 11, pp. 2184–2199, November 2010.

A. Kazemian, A. Salari, A. Hakkaki-Fard, and T. Ma, “Numerical investigation and parametric analysis of a photovoltaic thermal system integrated with phase change material,” Appl. Energy, vol. 238, no. September 2018, pp. 734–746, March 2019.

S. Agrawal and G. N. Tiwari, “Overall energy, exergy and carbon credit analysis by different type of hybrid photovoltaic thermal air collectors,” Energy Convers. Manag., vol. 65, pp. 628–636, January 2013.

F. Sobhnamayan, F. Sarhaddi, M. A. Alavi, S. Farahat, and J. Yazdanpanahi, “Optimization of a solar photovoltaic thermal (PV/T) water collector based on exergy concept,” Renew. Energy, vol. 68, pp. 356–365, August 2014.

F. Bayrak, N. Abu-Hamdeh, K. A. Alnefaie, and H. F. Öztop, “A review on exergy analysis of solar electricity production,” Renew. Sustain. Energy Rev., vol. 74, no. March, pp. 755–770, July 2017.

S. K. Sansaniwal, V. Sharma, and J. Mathur, “Energy and exergy analyses of various typical solar energy applications: A comprehensive review,” Renew. Sustain. Energy Rev., vol. 82, no. July 2017, pp. 1576–1601, February 2018.

M. Mustapha, A. Fudholi, C. Hoy Yen, M. Hafidz Ruslan, and K. Sopian, “Review on Energy and Exergy Analysis of Air and Water Based Photovoltaic Thermal (PVT) Collector,” Int. J. Power Electron. Drive Syst., vol. 9, no. 3, p. 1367, 2018.

Ì. B. Kilkis, “Utilization of wind energy in space heating and cooling with hybrid HVAC systems and heat pumps,” Energy Build., vol. 30, no. 2, pp. 147–153, June 1999.

I. Dincer, M. M. Hussain, and I. Al-Zaharnah, “Energy and exergy use in public and private sector of Saudi Arabia,” Energy Policy, vol. 32, no. 14, pp. 1615–1624, September 2004.

A. Kane, V. Verma, and B. Singh, “Optimization of thermoelectric cooling technology for an active cooling of photovoltaic panel,” Renew. Sustain. Energy Rev., vol. 75, no. September 2016, pp. 1295–1305, August 2017.

N. Dimri, A. Tiwari, and G. N. Tiwari, “Comparative study of photovoltaic thermal (PVT) integrated thermoelectric cooler (TEC) fluid collectors,” Renew. Energy, vol. 134, pp. 343–356, April 2019.

N. Dimri, A. Tiwari, and G. N. Tiwari, “Effect of thermoelectric cooler (TEC) integrated at the base of opaque photovoltaic (PV) module to enhance an overall electrical efficiency,” Sol. Energy, vol. 166, no. April, pp. 159–170, May 2018.

F. Rajaee, M. A. V. Rad, A. Kasaeian, O. Mahian, and W. M. Yan, “Experimental analysis of a photovoltaic/thermoelectric generator using cobalt oxide nanofluid and phase change material heat sink,” Energy Convers. Manag., vol. 212, no. March, p. 112780, May 2020.

C. Haiping, H. Jiguang, Z. Heng, L. Kai, L. Haowen, and L. Shuangyin, “Experimental investigation of a novel low concentrating photovoltaic/thermal–thermoelectric generator hybrid system,” Energy, vol. 166, pp. 83–95, January 2019.

Y. Maleki, F. Pourfayaz, and M. Mehrpooya, “Experimental study of a novel hybrid photovoltaic/thermal and thermoelectric generators system with dual phase change materials,” Renew. Energy, vol. 201, no. P2, pp. 202–215, December 2022.

N. Wang, L. L. Ni, A. Wang, H. S. Shan, H. Z. Jia, and L. Zuo, “High-efficiency photovoltaic-thermoelectric hybrid energy harvesting system based on functionally multiplexed intelligent thermal management,” Energy Convers. Manag., vol. 272, no. October, Nomber 2022.

T. Liao, Q. He, Q. Xu, Y. Dai, C. Cheng, and M. Ni, “Coupling properties and parametric optimization of a photovoltaic panel driven thermoelectric refrigerators system,” Energy, vol. 220, p. 119798, April 2021.

X. Wen, J. Ji, Z. Li, Z. Song, and T. Yao, “Performance characterization of a PV/T system employing micro-channel heat pipes and thermoelectric generators: An experimental and numerical study,” Energy, vol. 264, no. November 2022, p. 126182, February 2023.

T. Yin and Z. Z. He, “Analytical model-based optimization of the thermoelectric cooler with temperature-dependent materials under different operating conditions,” Appl. Energy, vol. 299, no. June, p. 117340, October 2021.

D. Zhao and G. Tan, “A review of thermoelectric cooling: Materials, modeling and applications,” Appl. Therm. Eng., vol. 66, no. 1–2, pp. 15–24, May 2014.

H. Najafi and K. A. Woodbury, “Optimization of a cooling system based on Peltier effect for photovoltaic cells,” Sol. Energy, vol. 91, pp. 152–160, May 2013.




DOI (PDF): https://doi.org/10.20508/ijrer.v14i3.14458.g8935

Refbacks

  • There are currently no refbacks.


Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is cited in SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics);

IJRER has been cited in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE in 2025; 

h=35,

Average citation per item=6.59

Last three Years Impact Factor=(1947+1753+1586)/(146+201+78)=5286/425=12.43

Category Quartile:Q4